Lock Making and Picking

anonymous@undisclosed.example.com (Anonymous) — Thu, 24 Nov 2022 12:41:28 +0000

:workshops:2016_deliveries:lock:20161215_0106.jpg

Lock Making and Picking

This workshop was developed at The Edge by Phil Gullberg and this version is from the second delivery at Woodford. 2016.

Summary

During this workshop you will learn how to make and pick a lock.

While at Woodford, you can follow along and download a pdf of this Workshop by connecting to our wifi network: TheEdgeWorkshop and downloading from the admin menu at the top right.

Step Zero: The Pin Tumbler Lock and Your Kit

Basic principles of the pin tumbler lock may date as far back as 4000 BC in Egypt.

The lock consisted of a wooden post affixed to the door, and a horizontal bolt that slid into the post. The bolt had vertical openings into which a set of pins fitted.

These could be lifted, using a key, to a sufficient height to allow the bolt to move and unlock the door.

In 1848, Linus Yale, Sr. invented the modern pin-tumbler lock.

In 1861, Linus Yale, Jr. was inspired by the original designed by his father.

He invented and patented a smaller flat key with serrated edges as well as pins of varying lengths within the lock itself.

The same design of the pin-tumbler lock is in use today.

How a Modern Pin Tumbler lock Works

The set pins keep the lock shut. They rest on top of the key pins which are kept in place by the barrel ridge. The key lifts the set pins above the shear line, allowing the lock to turn.

GIF time…..

Your Lock

Your lock kit contains a pin tumbler lock set in a padlock. The padlock is held shut with magnets when locked.

The bulk of your kit is made from cardboard to keep costs as low as possible.

This means that we can't make a barrel ridge that will stand up to the test of picking. So we've modified the the mechanism, with Orings on the key pins to keep them in place when locked.

Kit Parts

Please check you have all your cardboard parts

And all your other parts

Shared Tools

Some simple tools required during the workshop, these are shared.

Side cutters (for biting off skewers)
electrical tape
Scissors (for cutting tape)

Step One: The Plug

We'll start by putting our plug together. Before we start, make sure that the skewer holes in your cardboard segments are punched out, and note each plate has a number on the bottom front side.

Assemble the first five plates of the plug

Add the plastic plug supports. Carefully use the pointy end of a skewer to nudge the plastic plug supports into place

Then add two cover plates to hold it all together - plug plates #6 & #7

Now we will add another three plates.

(Note the notch in the left hand side of plates #8 & #9.) This is where one of our magnets will go… but we'll come to that in a moment

And again we add the plastic plug supports to these three layers

And then two more cover plates

You should be up to plug plate #12

Now add the last three layers of plug plates and the two plastic plug supports for each layer

And now get plug plate #16 on top to hold it all in place. You don't want it to fall apart

Step Two: Tape in Plug Magnet

Now we are going to add the magnet and tape it all together

Can you see the magnet in its notch on the left hand side (if you are looking at it from the front)?

Carefully remove the skewer on the left hand side of the assembled plug …

and starting here, tape around the “equator” of your plug…

Tape over the magnet…

Around the back…

Carefully remove the second skewer without disturbing the alignment of the layers

Trim the tape to the required length.

Make sure you are not compressing the cardboard too much but also that there isn't any space between the layers

Now we are going to push the pointy ends of the skewers through the tape and back into their holes

All the way through the plug and out through the tape on the front

Make sure the two skewers are flush on the back of the plug…

Now we are going to add the front cover for the plug

This front cover is 6mm, a bit thicker than the other layers, cut out of the double-ply corrugated cardboard that the hull parts are cut from

When you have this front cover in place, trim the skewers to the required length with the side cutters. Make sure you hold on to the bit you're cutting so it doesn't fly off and take out an eye!

Step Three: Fit Plug Sleeve

Now we are going to get our plug sleeve ready and test that the plug will spin smoothly inside it

Take your little piece of sandpaper and smooth off the rough edges on the plug sleeve

When you've done this insert the plug and check it turns smoothly in the sleeve

Step Four: Install Key Pins

Now we are going to install our key pins and test their function

The key pins are the three shorter dowels (24mm long) with a groove cut into them. Seat the Orings on to the three key pins

Insert the pins into each of the chambers…

and check their function (i.e. that they move up and down freely) by manipulating them using you pick via the key hole

If you have got this far...Congratulations!

You are now half way and the rest is super easy. (Insert sarcasm mark)

Step Five: The Hull

The hull consists of 10 layers:

1x front smaller hole (has etching on it)
1x back no hole (has The Edge logo on the back)
1x hasp layer
7x filler layers

First of all take your hasp layer and carefully remove it. We are attaching the other magnet to the hasp

Make sure the polarity matches the polarity of the magnets in the plug.

An easy way to do this is to put your plug in the white tube (to make the removal of magnets easier) and let the magnets snap together on the outside. This way you'll know which side should point in or out.

Make sure the magnet in the hasp doesn't stick out too much and add a piece of tape to keep it in place

Don't use too much tape as it will add unwanted friction

Put the hasp back into its layer before the next step

Now we start putting our Hull together

Just as we did with the Plug, start by aligning three of the Hull “Filler” plates on two of your skewers. Then add the Hasp layer of your lock.

Step Six : Construct Top Pin Chamber Assembly

The next step is to construct the top pin chambers and their supports.

The following parts make up the Top Pin Chamber Assembly:

3x metal tubes (45mm long)
2x plastic supports with regular size holes (same diameter as the tubes)
1x plastic support with smaller holes

Start by fitting the middle metal tube into the centre hole of one of the plastic supports

It could be a tight fit. Be patient and don't be afraid to ask for help

Now add the second plastic support

Align the outside holes of the plastic chambers supports and fit the other two metal chambers

Now shimmy the top plastic support up the metal chambers until it is about 5mm from the top of the chamber

It helps if you keep it as level as possible as you shimmy it up Make sure the metal chambers stay flush with the bottom surface of the the lower support

We'll now install the Top Pin Chamber Assembly into our half built Hull…

And slide the third of our plastic Chamber Supports (the one with the smaller holes) into the gap between the lower chamber support and the floor of the Chamber Assembly hole in the Hull Plates

This may require more patient shimmying

Step Seven: Complete Hull Assembly

We are now ready to complete the assembly of our Hull

Just add the remaining Hull Filler plates

Step Eight: Fit the Plug into the Hull

We use tape to ensure the sleeve fits snugly inside the hull and won't rotate when we operate the lock.

First, add a strip of tape around the circumference of the Sleeve (postal tube).

Start the tape next to the middle hole, wrap it around the sleeve and trim the tape near the other side of the hole

This snug fit also means that if we get the next bit wrong, it can be hard to reposition, so we need to be accurate as we fit the Plug Sleeve in to the Hull.

Now remove the bottom plastic chamber support (the one with the smaller holes) and line the hole in the Plug Sleeve (postal tube) with the Chambers. When you have this accurately aligned fit the sleeve by pushing down into the Hull

Now replace the bottom plastic Chamber Support

Step Nine: Install Set Pins

First deburr the set pins using the piece of sandpaper to ensure that they move freely in their chambers

Now install the springs. Make sure you have the springs up the right way

You want the smooth end at the bottom of the chamber and the rough end at the top of the chamber.

Hold your lock upside down the so the springs and pins don't fall out

Now install the pins into their chambers

Step Ten: Install the Plug in the Hull to complete the Lock Mechanism

Start by checking that your Key Pins are all sitting neatly in their Plug Supports…

and that none of the Set Pins or their springs have fallen out. (This will require patience!)

Orient the Plug so that the Key Pins and the Plug Support are at 90 degrees from the Chambers (i.e. 9 O'clock Position). The Chambers should actually be lined up with your tape

In one hand hold The Hull and Plug in position…

press the Set Pins one at a time so you can slide the plug into position

The back should look like this..

And the front like this

Step Eleven: Finishing Touches

Next we'll give our lock its finishing touches…

by adding the attractive “Limited Edition” back…

And Front Plates…

Add some rubber bands to keep it all together…

Add the last two skewers into their registration holes.

Finally, trim your skewers…

Congratulations!

You just made a cardboard Tumbler Lock!

The only thing now is to test if it actually locks.

And to pick it!

Step Twelve: Test and Pick Your Lock

To test your lock insert the long end of your tension bare (plastic “L” shape) into the square hole at the bottom of your key hole and rotate the plug until it is in the vertical home (12 O'clock) position

As you do this you should hear you lock click as the springs force the pins into position

Once it is in the 12 O'clock position and the pins are engaged, you should not be able to rotate the plug

To pick the lock insert your tension wrench and use it to apply a slight rotational force (torque) to the plug

Then use your pick, via the keyhole, to momentarily raise the each of the Key Pins

If you are doing this correctly the torque on the plug should provide a small ledge for the set pin to rest on at the “Shear Line”.

In our lock the shear line is the interface between the Plug Support and Plug sleeve.

It might help you to visualise this

Keep “picking” until you have all Set Pins resting on the ledge… when you do, the Plug will turn.

Good Luck!

And Remember

Production Notes

If you want to see how this workshop was put together, log in and check out the production notes

Pre-Production

anonymous@undisclosed.example.com (Anonymous) — Mon, 25 Jun 2018 13:10:22 +0000

Pre-Production

These materials are per participant if not specified otherwise:

1 x A3 corrugated cardboard sheet, 3mm
2 x A3 corrugated cardboard sheets, 6mm
1 x A3 coated acrylic 3mm (for picks, plug support chamber support 10 - per sheet)
1 x A3 Coated acrylic, 6mm (for tension wrenches - 30 per sheet )
1 x Postage tube, 51mm (O/D:60mm)
3 x 45mm metal pipe (I/D: 7-9mm O/D: 10mm)
3 x Retractable Ballpoint pen (for spring)
3 x Skewers (3mm diameter)
3 x 30mm Dowel (Diameter: 6mm)
3 x 25mm Dowel (Diameter: 6mm)
3 x O-ring (I/D: 4.1mm O/D: 7.3mm), Nitrile rubber
2 x strong mini magnets
Electrical tape
2 x Rubber bands (fit around the hull)
Sandpaper (not too rough)

Notes - 28 Nov 2016

Andrei and I looked out files for cutting and a hard copy protype of of the latest Lock as per Phil's instructions

20161106_lock_prep_woodford_pg_1_.pdf

We built the prototype from these parts and have got it working fairly well.

There are a couple of design files that need to be found or drawn up for:

the back plate of the hull
front Plate of the Hull (possibly with some branding- if we have time)
front cover for the plug (to hide the tape)

Here's the finished product without the Plug front and hull front

We'll cut one of these from scratch and assemble as a test before prepping boxes

Here's the exploded view of all parts without the three parts mentioned above

Notes - 01 Dec 2106

Found that the 3mm cardboard (which is actually 3.5mm) is too thick to cut plug parts have moved to 2.7mm pallet pad

Packing Instructions for Woodford

The Packing process has been designed to ensure the kits are presentable, parts are easy to find and in a logical order (to assist in delivery in the dark at Woodford) and can be easily check that all parts are in each kit

List of parts

Hull

6x standard hull plates 1x Front cover plate 1x back cover plate 1x Hasp plate

Plug/ barrel

7 x Key hole plates (#17 spare, 16, 12, 11, 7 & 6) 6x plug support plates (#15, 14, 13, 10, 5 & 4) 2x Plugsupport/magnet plates (#9 & 8) 1x Back plug plate 1x front plugg plate (6mm double ply card) 1x plug cylinder ( postage tube) 2x desiccant satchel

Timber parts

3x skewers cut in half (6x 1/2 skewers) 3x Top Pin (Dowel 30 mm) 3x Key Pins (Dowel 24mm with seat) 3x Orings

metal Parts

2x magnets 3x chamber 3x camber spring

Plastic parts

1x Chamber support (small holes) 2x Chambers support (regular holes) 1x Lock Pick 1x Tension Bar (6mm) 18x Plug supports 2x plug support spare

Files

This is where you put files for laser cutting etc..

20161128_lock_wf_2016-17.zip

Barrel/ Plug laid out on 280×730 for 2.5mm pallet pad

backup_of_barrelmb01122016.cdr

acrylic_parts_x_8_on_template.cdr

|frontplatehull.cdr

hull_v.101.cdr

lock_barrel-1.cdr

acrylic_parts_x_8_on_template_v1.cdr

SLQ Wiki workshops:public:lock-delivery-woodford

Lock Making and Picking

Lock Making and Picking

Summary

Step Zero: The Pin Tumbler Lock and Your Kit

How a Modern Pin Tumbler lock Works

Your Lock

Kit Parts

Shared Tools

Step One: The Plug

Step Two: Tape in Plug Magnet

Step Three: Fit Plug Sleeve

Step Four: Install Key Pins

If you have got this far...Congratulations!

Step Five: The Hull

Step Six : Construct Top Pin Chamber Assembly

Step Seven: Complete Hull Assembly

Step Eight: Fit the Plug into the Hull

Step Nine: Install Set Pins

Step Ten: Install the Plug in the Hull to complete the Lock Mechanism

Step Eleven: Finishing Touches

Congratulations!

Step Twelve: Test and Pick Your Lock

And Remember

Production Notes

Pre-Production

Pre-Production

Notes - 28 Nov 2016

Notes - 01 Dec 2106

Packing Instructions for Woodford

List of parts

Hull

Plug/ barrel

Timber parts

metal Parts

Plastic parts

Files