Handtools Induction - Practical Exercise

anonymous@undisclosed.example.com (Anonymous) — Thu, 03 Oct 2024 18:02:45 +0000

~~REVEAL~~

Handtools Induction - Practical Exercise

:facilities:fablab:inductions:handtools:screen_shot_2020-11-09_at_10.59.27_am.png

THIS WORKSHOP HAS NOT BEEN RUN SINCE 2022, IS AVAILABLE FOR ARCHIVAL PURPOSES ONLY. ANYONE SEEKING TO ADAPT THIS WORKSHOP SHOULD CONSIDER THE FOLLOWING INFORMATION.

WARNING - This workshop makes use of small coin cell/ button batteries.

In December 2020, the Australian Government made mandatory safety and information standards for button/coin batteries and consumer goods that contain button/coin batteries (the standards). The standards included an 18 month transition period and became mandatory from 22 June 2022. From 22 June 2022 manufacturers, importers, wholesalers and retailers of button/coin batteries or consumer goods that contain button/coin batteries supplied to Australia, must comply with the applicable Australian mandatory safety and information standards. Supplying or selling non-compliant products to consumers in Australia is illegal. The four mandatory standards are as follows:

• Consumer Goods (Products Containing Button/Coin Batteries) Safety Standard

• Consumer Goods (Products Containing Button/Coin Batteries) Information Standard

• Consumer Goods (Button/Coin Batteries) Safety Standard

• Consumer Goods (Button/Coin Batteries) Information Standard

Summary

Participants will assemble a laser cut LED badge and familarises themselves with the variety and safe use of hand tools in The Edge Fabrication Fab. This is the practical exercise for the Edges Hand tools induction.

The aim of the activity is to provide inductees with an opportunity to :

Gain a hands-on, practical understanding of the basic categories of hand tools found in in the Fabrication Lab
Identify the risks associated with these categories of tools and learn safety and handy tips for using these tools.
Put together an inexpensive, cool and quick little take-home project thats been made with the equipment in the Fabrication Lab.

Materials

Part #	Part Name	Image
Laser Cut Parts
1	badge front
2	logo
3	Battery retainer
4	Battery back

Other Parts
5	Cr2032 Calculator Cell (Battery)
6	Flashing 5mm LED (various colours)
7	M3 Nut
8	M3 12mm screw
9	Metal Badge Back

Parts Back

Parts Front

Tools

Hot glue gun & glue
Pointy nose pliers
Philips head screwdriver
Awl
Adjusting spanner
Countersinking bit
Cordless Drill
Hand saw
Clamp or mini vice
Sand paper

Assembly Instructions

Step Zero:

When ever you are in the Fabrication Lab

make sure you're keeping your space tidy

You are use correct manual handling technique

Check you have all you parts and that these are cut through cleanly.

Check you have all the tools you require… and the right tool for the job

For instance if you need to clean up laser cut parts, use an awl (not a screwdriver). An awl is designed for poking… screwdrivers are for driving screws.

Step One:

First, with the Cordless Drill and a counter sink bit, countersink the hole in the Battery back (Part 4)

make the counter sink about a match head deep

Any time you are using a spinning blade or tool you also need to be care careful not to get hair or clothes caught in the equipment… Take it off, tie it back or tuck it in

Also any time you are using a spinning blade or tool you could be creating friction… Be careful of hot tools and keep track of where your hot swarf ends up

Next, separate the Battery Retainer (Part 3) from the Battery Back by sawing the part in half.

Are you applying force? Make sure you secure your work… clamp the material down or put it in a vice when using a drill or saw

Step Two:

With hot glue, stick the Battery Retainer (part3) to the back of the Badge Front (Part1) make sure you have aligned the screw holes and LED holes on both parts.

your blob of glue should be about the size of a pea

Hot Glue Burns - if you manage to get hot glue on you skin cool it under cold running water immediately. trying to wipe it off will spread the burniness around.

Step Three:

Test your LED (part 6) by placing the long leg over the positive (+) of the Cell(battery)(part 5) and and the short leg over the negative (-) side.

with pliers bend the short leg over at 90 deg and back on itself

orient the LED so the short bent leg is inboard- towards the cell (battery) and the positive (+) long leg is outboard.

Step Three: - Continued

Turn the badge over so you are looking at the face and hot glue the LED in the hole in this position from the front

Turn the badge over again so it is face down and insert the Cell (battery) with the positive (+) up.

Step Four:

Bend the long positive leg over the Cell and back on itself

The LED should Light up.

Step Five:

Align the Battery Back (Part 4) screw hole with the screw hole in the badge front/ battery retainer.

Insert Screw (part) from back to front and screw on nut.

Allow nut to seat in captured nut recess on Badge Front

Tighten Nut and bolt using Phillips head screwdriver and adjustable spanner.

Step Six

hot glue the badge back

Hot glue the Logo over the LED

3D explodable view online

Complete the General Induction Online

Now its time to complete your General Induction online quiz. Go to State Library's inductions site.

You will be asked to log-in - use the SSO option

Select the General Induction

Click on enroll

And start your assessment

Drag the cross-hairs (not the mouse) over the correct answer.

13032021_handtoolsbadgefntnested_captured_nut.cdr

Preparation

This workshop requires

the below to be cut out on the laser. Total cutting/ etching time (for 60 parts) = 1.5 hours

Files

Badge fronts

New Corel file to suit new machine profiles. Just print as colour with 6.9mm plywood profile or use this trotech job file.

Badge Backs

Badge backs handtools_induction_backs.cdr are to be cut on 4mm plywood

ARCHIVED: Handtools Induction

anonymous@undisclosed.example.com (Anonymous) — Thu, 01 Apr 2021 13:18:51 +0000

ARCHIVED: Handtools Induction

24 July 2017

handtools_inducn_v4trainer.pdf

handtools_inducn_v4assess.pdf

Redevelopment Feb 2018

In Feb 2018 the Hand tools induction was separated from the soldering induction and was redeveloped as a minimum standard OH&S induction in the Fabrication Lab. The Concept was that any person entering the Fabrication Lab ( who is not just visiting ) will complete this 10 min induction before checking in for the first time. Without this handtools induction you can't even pick up a screwdriver or craft knife. Other aims connected to this redevelopment were to enable us to

safely and quickly engage newcomers to the fab lab whether as an individual or in a group/workshop context.
to quickly give newcomers a sense of membership/ownership of the resources and to encourage return visitation - now that they are officiallyinducted.
As per all Edge workshops participants leave with a takeaway.
The email confirming newly inducted participants is an opportunity for promotion of Fab Lab and other resources.

This new induction process can be broken into 4 sections

Applying for an Edge booking account.
Induction Slideshow
Induction Assessment
Induction practical activity

1. Apply for an Edge booking account

participants fill out booking account form on pc or ipads

2. Handtools induction Slideshow

Participants click through a slideshow detailing

their responsibilities in the space
the types of hand tools the Edge has
the safety tips associated with each of these types of tools

The Edge OH&S Basics and Handtools Induction Slideshow

3. Induction assessment

Participants fill out (paper form) / click thru (gamified digital) assessment to demonstrate competency.

4. Induction practical exercise

Participants use a range of handtools in the The Edge fablab to assemble a badge. See workshop instruction

SLQ Wiki facilities:fablab:inductions:handtools

Handtools Induction - Practical Exercise

Handtools Induction - Practical Exercise

Summary

Materials

Parts Back

Parts Front

Tools

Assembly Instructions

Step Zero:

Step One:

Step Two:

Step Three:

Step Three: - Continued

Step Four:

Step Five:

Step Six

Complete the General Induction Online

Preparation

Files

Badge fronts

Badge Backs

ARCHIVED: Handtools Induction

ARCHIVED: Handtools Induction

Redevelopment Feb 2018

1. Apply for an Edge booking account

2. Handtools induction Slideshow

3. Induction assessment

4. Induction practical exercise